|
Product Details:
|
| Product Name: | Ceramic Hybrid Angular Contact Ball Bearing | Model Number: | 7008C P4A |
|---|---|---|---|
| Bore Diameter: | 40 Mm | Outside Diameter: | 68 Mm |
| Width: | 15 Mm | Contact Angle: | 15 Degree |
| Rolling Body: | Si3N4 Ceramic Ball G5 | Cage: | PEEK Cage |
| Accuracy Class: | P4A / ABEC-7 | Lubrication: | Kluberspeed NBU15 Grease |
| Highlight: | ceramic hybrid angular contact bearing,7008C P4A spindle bearing,24000RPM machine tool bearing |
||
The 7008C P4A ceramic hybrid angular contact ball bearing is built for machine tool builders who need spindle accuracy that survives thousands of hours of continuous high-speed rotation. Instead of conventional through-hardened steel balls, this bearing carries grade G5 silicon nitride ceramic balls inside P4A ground chrome steel rings — a combination that removes the most common cause of spindle temperature drift.
Silicon nitride balls weigh roughly forty percent less than steel balls of the same diameter, so centrifugal force at the outer ring stays low even when the shaft turns at 24000 rpm. Lower centrifugal load means less skidding, lower friction torque and a cooler outer ring, which is exactly what keeps preload stable during long roughing cycles. The ceramic raceway contact also resists adhesive wear, so the bearing keeps its original clearance far longer than an all-steel unit working under identical conditions.
The rings are machined from vacuum-degassed bearing steel, hardened, then ground and superfinished on four-point controlled machine tools to P4A tolerance. Bore and outside diameter runout are held within two micrometres, and the 15-degree contact angle is verified on every single piece. A machined PEEK cage guides the balls with minimum friction and will not smear if the spindle is accidentally run dry for a short period — an important safeguard on unattended night shifts.
Each bearing is preloaded to a light class and matched for universal pairing, so two units can be installed back-to-back, face-to-face or in tandem without further adjustment on the customer side. The factory fills the bearing with a measured charge of Kluberspeed NBU15 grease and dynamically balances the assembled pair, allowing the spindle builder to bolt the set in and go straight to running in.
| Parameter | Specification |
|---|---|
| Bore diameter d | 40 mm |
| Outside diameter D | 68 mm |
| Width B | 15 mm |
| Contact angle | 15 degree |
| Basic dynamic load rating Cr | 19.5 kN |
| Basic static load rating Cor | 14.2 kN |
| Limiting speed, grease | 19000 rpm |
| Limiting speed, oil air | 30000 rpm |
| Rolling body | Si3N4 ceramic ball, G5 |
| Cage material | PEEK |
| Accuracy class | P4A / ABEC-7 |
| Recommended preload | Light, approx. 100 N |
This bearing fits horizontal and vertical machining centre spindles, high-speed drilling heads, engraving and milling spindles, internal grinding quills and motorised spindle cartridges where the front pair must run above 20000 rpm. It is also a direct replacement for steel ball bearings in woodworking routers, PCB drilling equipment and precision boring heads that suffer from thermal growth at the tool tip.
Because the ceramic balls insulate heat, the bearing transfers less friction energy into the housing, so aluminium and cast iron spindle housings stay dimensionally stable. Customers rebuilding high-frequency spindles typically report lower vibration values at the tool holder after switching to this hybrid configuration.
Every bearing leaves the factory in an individual vacuum anti-rust bag with a traceable serial label, then sits in a foam-lined company brand box. Cartons are reinforced and palletised for sea or air freight, and matched pairs are packed together so the set number is never separated in transit.
Quality control covers incoming steel certification, 100 percent raceway profile inspection, noise and vibration testing on a BVT tester, preload verification and a final run-in at 60 percent of limiting speed. Ceramic ball lots are checked for grade and ovality before assembly. Documentation including material certificates, dimensional report and packing list is issued with each shipment, and technical support for mounting and lubrication selection is available throughout the service life.
Contact Person: Xu
Tel: 18762631303
Fax: 86-0510-85117986